Object 257

[ZakTheBuilder1]

"the Object 257, the bridging in between the failed IS-6 and the renowned IS-7."

DESIGN
As mentioned earlier, many elements from the IS-6 program were used in Object 257. The turret and pike nose came from the Object 252U and the engine and transmission from the Object 253. However, one of the main focuses of the Object 257 project was sturdier protection. The same principle applied on the pike nose, which was implemented on the side of the hull as well. The previously flat hull sides were now angled inwards at an extreme angle, forming a diamond shape silhouette from the front and rear. On the downside, this caused huge internal problems. Primarily, torsion bars could no longer be used, since the hull was too narrow, meaning that the suspension had to be moved on the outside of the hull. For the suspension, four volute springs were mounted on each bogie, with two wheels per bogie, a very similar design to that of the American M4 Sherman. This made the Object 257 one of the most unique looking Soviet heavy tanks of the post-war era, as this was the first time a Soviet tank used volute spring suspensions.

The turret was identical to that of the Object 252U, being heptagonal and of a low profile. Inside, the gunner was seated to the left of the gun, with the commander behind him. The loader was located to the right of the gun. A coaxial machine gun was also mounted to the right of the gun, and could be fired by the gunner. It is unclear if it was a 7.62 mm SGMT machine gun or a 12.7 mm DShk heavy machine gun. The loader was responsible for loading this weapon as well.

ARMOR
One of the most interesting aspects of this tank is the armor layout. The pike nose was an increasingly common feature in Soviet heavy tanks of the time. It was 150 mm (6 inches) thick, angled at 28° from the side. Yet the lower hull was completely new. Instead of flat plates, like on the IS-6, the plates were angled inwards, forming the same effect as a pike nose. This would have helped immensely against incoming rounds, deflecting them into the ground. The top parts were 150 mm (6 inches) thick and angled at 30°. The bottom plates were 85 mm (3.3 inches) thick angled at 23°. This thickness was not maintained all the way to the bottom of the hull. Halfway in, the armor was thinned down to only 20 mm (0.8 inches) yet kept at the same angle. This was most likely done to save weight, as the chances of enemy fire hitting this area were rather low, with the large suspensions being in front. The new side armor was impenetrable to the German 105 mm Flak 39 and the front was even strong enough that the BL-13-1 gun could not penetrate it at point-blank range. The turret armor was thick as well. The sides, although tinner in some areas, since they were curved, were 150 mm (6 inches) thick, angled at 45° degrees. Of course, this came at a cost. The weight of the hull increased to 23 tonnes (25.3 tonnes) over the IS-6’s 21 tonnes (23 tonnes).

FATE?
After the discovery of the Maus and Jagdtiger and their analysis, the armor on the Object 257 was deemed insufficient. The 128 mm KwK 44 guns of the Jagdtiger and Maus would have pierced the hull. Likewise, the armor on the Maus and Jagdtiger was too strong for the BL-13. All this meant that the Object 257 needed to be reworked significantly. In addition, on 11th June 1945, the requirements of a new heavy tank were set by the GABTU. The weight increased to 60 tonnes (66 US tonnes) and the new armament was to be an S-26 130 mm gun. Lastly, torsion bar suspension was required. The Object 257 clearly was not adequate, leaving factory No.100 to start work on a new heavy tank. Nonetheless, work was not in vain, as the experience gained and armor features of the Object 257 were passed on. Many other tanks were designed, until the final Object 260 was made, the IS-7 we know today.

ROLE IN GAME
A cheap IS-7

LINK
https://tanks-encyclopedia.com/object-257/